Close Menu
  • Modern Home
    • Bedding & Sleep
      • Bed Linens
      • Mattress Guides
      • Royal Aesthetics
      • Sleep Hygiene
    • Home Decor & Styling
      • Color Palettes
      • Lighting Design
      • Minimalist Trends
      • Wall Colors & Art
    • Furniture & Cabinetry
      • Bedroom Furniture
      • Living Room Furniture
      • Custom Cabinetry
      • Dining & Kitchen
  • Creative Crafts
    • Sewing & Craft
      • Sewing Basics
      • Sewing Patterns
      • Sewing Projects
      • Fabric Guides
    • Embroidery
      • Hand Embroidery
      • Machine Embroidery
      • Embroidery Patterns
      • Stabilizers & Trims
    • Quilting
      • Quilting Basics
      • Quilt Patterns
      • Quilt Projects
      • Binding & Finishing
  • Tools & DIY
    • Home Improvement
      • DIY Repairs
      • Hardware Guides
      • Workshop Safety
      • Space Planning
    • Cleaning & Organization
      • Home Hacks
      • Organization Systems
      • Laundry Care
      • Storage Solutions
  • Buying Guides
    • Equipment & Machinery
      • Sewing Machines
      • Embroidery Machines
      • Quilting Machines
      • Sergers
    • Tools & Appliances
      • Large Appliances
      • Small Appliances
      • Power Tools
      • Thread & Notions
  • Company Info
    • Contact
    • Privacy Policy
    • Terms and Conditions
Facebook X (Twitter) Instagram Pinterest
Facebook X (Twitter) Instagram
CraftsingCraftsing
Monday, November 16
  • Modern Home
    • Bedding & Sleep
      • Bed Linens
      • Mattress Guides
      • Royal Aesthetics
      • Sleep Hygiene
    • Home Decor & Styling
      • Color Palettes
      • Lighting Design
      • Minimalist Trends
      • Wall Colors & Art
    • Furniture & Cabinetry
      • Bedroom Furniture
      • Living Room Furniture
      • Custom Cabinetry
      • Dining & Kitchen
  • Creative Crafts
    • Sewing & Craft
      • Sewing Basics
      • Sewing Patterns
      • Sewing Projects
      • Fabric Guides
    • Embroidery
      • Hand Embroidery
      • Machine Embroidery
      • Embroidery Patterns
      • Stabilizers & Trims
    • Quilting
      • Quilting Basics
      • Quilt Patterns
      • Quilt Projects
      • Binding & Finishing
  • Tools & DIY
    • Home Improvement
      • DIY Repairs
      • Hardware Guides
      • Workshop Safety
      • Space Planning
    • Cleaning & Organization
      • Home Hacks
      • Organization Systems
      • Laundry Care
      • Storage Solutions
  • Buying Guides
    • Equipment & Machinery
      • Sewing Machines
      • Embroidery Machines
      • Quilting Machines
      • Sergers
    • Tools & Appliances
      • Large Appliances
      • Small Appliances
      • Power Tools
      • Thread & Notions
  • Company Info
    • Contact
    • Privacy Policy
    • Terms and Conditions
CraftsingCraftsing
Home»Sewing & Craft»Sewing Projects»Make a Shirt Collar Pattern in 8 Steps: Draft, Cut, Sew
Sewing Projects

Make a Shirt Collar Pattern in 8 Steps: Draft, Cut, Sew

MithuBy MithuUpdated:November 16, 202622 Mins Read
A finished crisp white dress shirt with a neatly sewn point collar laid flat on a light wooden table, collar points sharp and symmetric
Share
Facebook Twitter LinkedIn Pinterest Email
Table of Contents Toggle
  • Shirt Collar Pattern Anatomy: Two Pieces and One Measurement
  • Measure the Neckline for a Shirt Collar Pattern
  • Draft the Collar Stand
  • Draft the Collar Leaf
  • True the Shirt Collar Pattern Before Cutting Fabric
  • Choose Fabric and Interfacing
  • Cut the Shirt Collar Pattern Pieces
  • Sew the Collar Leaf
  • Turn, Grade and Press the Points
  • Understitch So the Seam Stays Hidden
  • Sew the Collar Into the Stand
  • Attach the Stand to the Shirt Neckline
  • Topstitch and Final Press
  • Check the Fit Before the Buttonholes
  • Collar Shapes You Can Draft From the Same Stand
  • Troubleshooting Shirt Collar Patterns
  • Frequently Asked Questions
  • Conclusion
  • About This Guide

⚡ Quick Answer: how do I make a shirt collar pattern?

To make a shirt collar pattern, measure the neckline along the seam line and add 5/8 inch for the placket. Draft a stand strip at that length, 1.25 inches tall, then a collar leaf about 3/8 inch shorter. Cut two of each, interface one of each pair, and sew.

A shirt collar pattern is two shapes and one measurement: a stand strip that follows your neckline, and a collar leaf that folds over it. Draft the pair once from your own shirt and you can cut the same two pieces for every shirt, blouse and dress at home, in any fabric weight and at any size.

The method below works from a finished shirt you already own, so there is no bodice block to draft first and no pattern to buy. You measure, you draw two rectangles, you curve three lines, and you have a reusable shirt collar pattern in about twenty minutes. If shirt making is new to you, the complete beginner sewing guide covers the machine basics first.

Building the rest of the shirt as well? The burrito method yoke tutorial gives the clean shoulder finish that sits above this collar, and the striped and plaid matching guide keeps the pattern aligned across the stand.

Drafting the stand and leaf on paper, then building the collar

This video is a general demonstration from the Sewing For A Living channel. Your machine’s thread path, settings and accessory list can differ, so follow the manufacturer documentation for your exact model and use the video to see the hand movement, not to copy the dial positions.

Shirt Collar Pattern Anatomy: Two Pieces and One Measurement

Every classic shirt collar is built from a collar stand and a collar leaf. The stand is the short band that wraps the neck and joins the shirt at the neckline. The leaf is the visible part with the points that folds down over the stand. Cut the leaf too long and it will not sit flat on the stand. Cut the stand wrong and the collar will either strangle the wearer or gape open at the throat.

One rule settles most of the drafting. The stand follows the neckline, so its length is driven entirely by the seam you are going to sew it into. The leaf follows the stand, so its length is driven by the stand. Work in that order and the two pieces always agree.

A finished shirt collar opened out to show the upright stand band and the pointed leaf that folds over it
The stand sits against the neck and the leaf folds over it
PieceWhat it controlsTypical adult shirt
Collar standFit around the neck1.25 to 1.5 inches tall at center back
Collar leafThe visible fold and points1.5 to 2.5 inches tall at center back
Seam allowanceBulk inside the collar3/8 inch on all edges

Measure the Neckline for a Shirt Collar Pattern

Measure along the seam line, never along the cut edge. A seam line runs 3/8 inch inside the raw edge on most commercial patterns, and measuring the raw edge instead adds up to three quarters of an inch of error on a single neckline. That error is the reason so many home-sewn collars end up slightly too long.

Close the front placket before you start. Button the shirt, or pin the button stand flat if the placket is unsewn, so the opening cannot drift apart while the tape moves around the curve. Lay the shirt flat and run the tape from center front, around the back of the neck, to the other center front. Note the marking at center back and at each shoulder seam, because you will transfer all three to the pattern.

A hand measuring the neckline curve of a shirt with a measuring tape while marking the collar length on paper, tailor chalk nearby
Measure along the seam line with the placket closed

Add 5/8 inch in total for the button overlap on a standard placket. Use 1 inch if your placket is wide or you want a roomier neck. Write the final number on the paper before you draw anything. Worked example: a 15.5 inch neck takes a neckline seam of about 15.75 inches, plus 0.75 inch of overlap, which gives 16.5 inches. Half of that is 8.25 inches, and that is the length you measure from the fold on the stand pattern.

Sewing for a growing child or a gift you cannot fit? Measure the finished garment that already fits. A neckline that already fits is a better guide to collar length than a tape measure around someone’s throat.

Draft the Collar Stand

Fold a sheet of pattern paper in half and line the fold up with center back, so you draft half a stand and open it out as one symmetrical piece. Set up the rectangle first, then shape the top edge.

  • Length: half your finished neckline number, measured from the fold outward.
  • Height at center back: 1.25 inches for a standard shirt, 1.5 inches for a taller band.
  • Height at center front: 0.75 inches, which is the taper that lets the collar sit against the collarbone and keeps it from standing to attention.
  • Shoulder notch: mark the distance from center back to the shoulder seam on the bottom edge.
  • Grainline: draw it parallel to the center back fold so it never runs along the length of the strip.

Now square up from the center back point by the back height and draw the top edge. Square up from the front by the front height. Join the two with a gentle curve using a French curve or a hip curve, and keep the curve shallow: a stand that is shaped too aggressively will cup away from the neck. Drop the front corner by about 1/8 inch so the point tucks under the leaf when the collar closes.

Raise the center front by half the difference between your flat neckline measurement and your actual neck circumference. On that same 16.5 inch neckline and a 15.5 inch neck the gap is 1 inch, so the rise at center front is 0.5 inch. That sounds fussy and it is the single change that separates a stand that lies flat from one that gapes. A rule of thumb is 1 inch or 2.5 cm of rise at center front, smoothed back into the shoulder notch with a curve.

Add 3/8 inch seam allowance to the top and bottom edges and to the front edge, and none at the center back fold. Label the piece: center back fold, center front, shoulder notch, and the grain arrow.

Paper collar and collar stand pattern pieces taped to a large sheet of pattern paper on a work table
Two rectangles become a stand and a leaf once curved

Draft the Collar Leaf

The leaf starts from the stand, and this is where most first drafts go wrong. Measure the length of the stand’s top edge, the curved one, and cut the leaf’s inner edge about 3/8 inch shorter than that measurement. The leaf has to travel over the curve of the stand’s folded edge, so a leaf the same length as the stand will ripple and fight itself at the shoulder.

Set the leaf height at 1.5 to 2.5 inches at center back, depending on how bold you want the collar. Height at the point is a separate decision from height at center back. A 2 inch leaf with a 2.75 inch point gives a classic spread. A 2 inch leaf with a 1.5 inch point reads as a button-down.

A pencil drawing a pointed collar leaf on pattern paper beside a finished collar stand and a French curve
Draw the leaf from the stand top edge

Draw the leaf on the fold as well, so center back lands on a fold and the piece opens out whole. Square down from the inner edge by the leaf height, then shape the outer edge. Take the transition from the side of the leaf into the point with a straight line for a sharp point or a curve for a rounded one.

Add a roll allowance of 1/8 inch to the outer edge of the leaf you will use as the upper collar, or cut one leaf 1/8 inch wider all around. The extra eighth is what makes the seam disappear underneath once the collar is turned, and it is the difference between a homemade collar and a shirt collar.

Finish with 3/8 inch seam allowance everywhere except the center back fold, and mark the same center back fold, shoulder notch and center front positions that you put on the stand.

True the Shirt Collar Pattern Before Cutting Fabric

Trueing is the step that catches drafting errors while they are still free to fix. Walk the seams with a tape or a flexible ruler. Hold the stand’s bottom edge upright against the shirt neckline, seam line to seam line. Check that the notches land at the shoulder seam on both sides. Then hold the leaf’s inner edge against the stand’s top edge and check that the ends meet at the front with 3/8 inch to spare.

If the stand is long, take the excess out of the two front ends in equal amounts so the collar stays symmetrical. If the stand is short, add the difference at center back, where no notch or point is affected. Write the corrections on the paper and cut a fresh copy, because a pattern with three sets of pencil corrections is one you will misread at midnight.

A paper collar stand pattern pinned onto an unstitched shirt neckline with a measuring tape run along the seam line
Walk the stand pattern against the neckline before cutting

Choose Fabric and Interfacing

Medium weight cotton shirting, poplin, oxford cloth and linen all draft and sew well in this shape. Avoid anything with stretch for a first attempt. A knit or a bias-cut collar will stretch out of shape between the pattern and the machine, and the stand will be too big before you sew a single seam. If you love a slippery fabric, cut and fuse it before it has a chance to move.

Interfacing carries the character of the finished collar. Fuse a light to medium woven fusible to the leaf and a slightly firmer fusible to the stand. Woven interfacing has grain and behaves like the shirting underneath, so it curves around the neck without cracking at the fold. A stiff non-woven in the leaf produces a board-like collar that will not roll and will show every wrinkle in the seam.

A shirt collar pressed over a tailor's ham with the iron lifted just above the fabric
Press over a ham so the collar keeps its curve
PieceInterfacing weightWhat it does
Collar leafLight to medium woven fusibleKeeps points crisp and allows the roll
Collar standMedium woven fusibleHolds the band upright at the neck
Detachable collarFirm fusibleHolds shape with no shirt seam to support it

Only one leaf and one stand get interfaced in a two piece collar. Fuse the interfacing to the wrong side of the piece that will sit underneath. The soft upper layer then rolls over the top and hides the seam. Press with a lifting motion and let the piece cool flat before moving it, because a hot fusible can shift after the iron lifts.

A steam iron fusing interfacing onto the wrong side of a gray cotton collar piece
Fuse the interfacing to the wrong side, then let it cool flat

Cut the Shirt Collar Pattern Pieces

Cut two leaf pieces and two stand pieces from the main fabric. Cut two of each from the interfacing unless you are fusing a larger sheet. Place the center back edge on a fold, check that the grainline on the paper runs parallel to the selvedge, and cut with sharp shears so the edges are clean enough to grade later.

Transfer every mark through the paper with tailor’s chalk or a tracing wheel: center back, center front, shoulder notch, and a small clip at the point of the leaf. The clips are what let you pivot at the point without guessing where the corner is.

A single curved collar stand piece with pins along its length, photographed on a green self healing mat
A cut collar stand piece pinned onto a gridded cutting mat

Sew the Collar Leaf

Place the two leaf pieces right sides together and pin along the outer edge, leaving the inner edge open. Start at one end of the inner edge and stitch around the outside with the seam allowance you drafted. Reduce the stitch length to about 2 mm as you approach each point. Take one stitch across the pivot, then lift the presser foot with the needle down to turn the fabric.

Shortening the stitch at the corner is what allows the point to hold its shape after turning. A long stitch at a sharp corner pulls open when you push the point out. Seal the seam with a backstitch at each end so the corner does not unravel during the grading that comes next.

A sewing machine stitching the outer edge of a collar with the needle pivoting at the point
Stitch the outer edge and pivot at every point

Needles matter more here than in the rest of the shirt, because the collar runs through three and four layers at the points. A fresh Universal 80/12 is the right match for midweight cotton shirting: SCHMETZ Universal 80/12 needles, 5 pieces. A dull needle bends at the corner, which is where a bent needle turns into a skipped stitch at the exact place you cannot hide.

Do not clip the pivot stitches yet. Turn the leaf right side out first and check that both points are sharp before you trim anything.

Turn, Grade and Press the Points

Grading makes a collar look flat and professional on the outside. Trim the seam allowance in the under layer down to 1/8 inch and leave the upper layer at 3/8 inch. When the leaf is turned, the two layers occupy different amounts of space, so the seam flattens and the layers stop stacking up inside the point.

Cut diagonally across each corner, stopping about 1/16 inch from the stitching. Trim the curved seam at the leaf ends down to 3/8 inch so it turns without puckering. Clip the curve at the ends of the leaf a few times if it insists on bubbling when turned.

Small scissors cutting diagonally across a collar point with the seam allowances trimmed to different widths
Grade the seam and trim diagonally across the point

Turn the leaf through the open inner edge, then work each point out with a point turner or the blunt end of a chopstick. Push from inside the point, never from the tip, so the fabric is supported while it turns. Press the leaf flat with the seam rolled slightly toward the under layer, which lifts the seam off the visible face and keeps the edge crisp.

Press on a tailor’s ham or a rolled towel so the leaf curves as it will on the body. A flat ironing board flattens a collar into a shape it will never hold on a shirt.

Understitch So the Seam Stays Hidden

Understitching is a single line of machine stitching through the seam allowances only, worked from the under side, close to the seam. It pulls the seam allowances toward the underside and stops the upper layer from rolling up and showing the join. It is one step most collar tutorials skip, and the cheapest upgrade available to a home-sewn collar.

Open the seam allowances flat with your fingers and stitch about 1/16 inch from the seam line, catching both allowances and the under layer underneath. Keep the upper layer folded clear of the needle. When you turn the collar over, the seam sits inside the fold, out of sight.

Machine understitching run through the seam allowances only, close to the collar seam
Understitch through the allowances so the seam stays inside

Understitch before you press. Pressing first sets the seam where it is, and the understitch then has to fight the crease. Sew it while the seam is still soft, press once, and the neckline edge stays where you put it through every wash that follows.

The inside of a turned shirt collar with a line of stitching through the open seam allowances
Stitch through both allowances with the upper layer held clear

Sew the Collar Into the Stand

Sandwich time. Place one stand piece right side up. Lay the finished leaf on top with the raw edges even and the leaf facing up, then lay the second stand piece on top, right side down. Pin through all three layers at center back first, then at the shoulder notches, then at the two front ends.

A finished collar sandwiched between two stand pieces with the notch marks matched
Match center back, then the shoulder notches, then the ends

Sew along the stand’s top edge through all the layers. Trim the seam allowance to 1/4 inch, clip the curve at the shoulder, and turn the stand right side out through the open ends at the front. The stand should now look like a narrow tube with the leaf emerging from the top seam.

Press the stand with the seam allowances inside and check that the leaf is even on both sides. If one side of the leaf sits higher than the other, one front end of the stand was cut short and needs marking before the next version.

Turning the leaf, building the stand and joining the two

This video is a general demonstration from the Euniceabby Fashion channel. Your machine’s thread path, settings and accessory list can differ, so follow the manufacturer documentation for your exact model and use the video to see the hand movement, not to copy the dial positions.

Attach the Stand to the Shirt Neckline

Staystitch the shirt neckline 1/8 inch inside the seam line before anything else goes on. A neckline that is still an open curve will stretch to fit almost anything you place against it, and the collar will end up long. Staystitching locks the length you measured at the start.

A collar stand piece pinned right sides together along an unstitched shirt neckline on a flat table
Pin the stand to the neckline, matching center back and both shoulders

Pin the outer stand to the neckline right sides together, matching center back, both shoulder notches and both front edges. Sew with the stand facing up so you can see where the layers run. The stand’s front end should finish flush with the finished edge of the button placket, or 1/8 to 1/4 inch short of it if you want the collar tips to clear a tie knot.

Clip the neckline seam allowance at the curves, press the seam up into the stand, then fold the inner stand down so its raw edge is enclosed. Tuck the fold under and pin from the right side so the pins run through the existing seam.

Topstitch and Final Press

Topstitch around the outside of the stand, starting at one front end and finishing at the other, with the stitch running through the fold of the inner stand. A distance of 1/16 to 1/8 inch from the edge reads as a professional edge stitch. Keep the line parallel by watching the edge of the presser foot while the needle tracks its own line.

Close-up of even topstitching around the outer edge of an attached collar
One even line of edge stitching around the finished collar

Press the finished collar flat, then fold the leaf down over the stand and press only the fold, using the tip of the iron and no steam. Steam at this stage softens the interfacing you just spent time fusing. Let the collar cool completely before you move it.

Check the Fit Before the Buttonholes

Button the collar on the wearer or on a dress form and look at three things. The stand should touch the neck at the back with no visible gap. The leaf should sit level, with both points the same distance from the placket. The collar should close comfortably, with about one finger of room between the stand and the throat.

A finished collar around a buttoned white shirt with a measuring tape looped around the collar
Button it up and check for a gap at the back

A stand that gapes comes from too much length or too little rise at center front. A stand that pinches comes from too little length, and the fix is to add the shortfall at center back and redraft the leaf to match. Both errors are cheap to correct on paper and expensive to correct after the buttonholes are cut.

Collar Shapes You Can Draft From the Same Stand

Once the stand fits, the leaf becomes a design decision and the fitting work is already done. Every shape below uses the same stand and the same inner edge length, so you can change the look of a shirt without remeasuring anything.

Three paper collar leaf shapes fanned out to show a narrow point, a spread point and a rounded button-down
One stand, three leaves: sharp, spread and button-down
StyleChange to the leafWhere it belongs
Classic pointLong point, tips 2.5 to 3 inches apartDress and office shirts
SpreadShorter point, tips 3 to 3.5 inches apartSuit shirts and formal wear
Button-downRounded point plus a buttonhole in each tipOxford cloth and casual shirts
Rounded or Peter PanCurve the point into a smooth arcBlouses and vintage styles
MandarinDrop the leaf and keep the standSummer shirts and tunics

For a one-piece collar with no separate stand, draft the stand piece taller and add the roll directly to the top edge, then fold the whole piece over. The result is softer and sits flatter at the front, which suits camp collar styles on linen.

Troubleshooting Shirt Collar Patterns

ProblemUsual causeFix
Points curl upwardNo interfacing, or too light in the leafFuse a woven interfacing and press with the seam rolled under
Stand gapes at the neckStand too long, or no rise at center frontRaise center front and shorten the two front ends evenly
Stand pinchesStand too short for the neckAdd the shortfall at center back and redraft the leaf
Bulk at the pointNo grading before turningGrade to 1/8 inch on the under layer and trim the corner diagonally
Seam shows on the outsideNo roll allowance and no understitchingCut the upper leaf 1/8 inch wider and understitch the seam
Collar tips too far apart or too closePoint spread set without a planRedraw the outer edge with the tip distance from the table above

If two problems show up at once, fix the stand first. Nearly every visual problem in a finished shirt collar traces back to the length or the height of the band around the neck. No amount of pressing will rescue a stand drafted against the wrong measurement.

A hand using a point turner on a turned collar point while small scissors rest on the table
Sharpen a lazy point with a turner before pressing

Frequently Asked Questions

How do I make a shirt collar pattern from scratch?

Measure the neckline along the seam line with the placket closed and add 5/8 inch for the button overlap. Draft a stand strip at that length, 1.25 inches tall at center back and tapering to 0.75 inch at center front. Draw the collar leaf from the stand’s top edge, about 3/8 inch shorter, and add 3/8 inch seam allowance to both pieces.

What size should a shirt collar stand be?

On an adult shirt the stand is 1.25 to 1.5 inches tall at center back and about 0.75 inch at center front. The height at the back sets how tall the finished collar looks, and the drop at the front is what lets the collar sit against the neck and keeps it from standing away.

How much seam allowance does a collar need?

3/8 inch on all edges of both the stand and the leaf. That allowance is easy to grade down to 1/8 inch in the under layer, which removes bulk from the point. Commercial patterns often use 5/8 inch, so trim those pieces to 3/8 inch before you cut fabric.

Is a shirt collar pattern the same for men and women?

The drafting method is identical. Men’s shirts usually take a 1.25 to 1.5 inch stand with a longer point, and women’s blouses often use a slightly shorter stand with a softer roll. Change the leaf height and the point spread and one pattern serves both.

Do I need a special presser foot to sew a collar?

A standard zigzag or straight stitch foot works. An edge stitching foot with a blade guide makes the topstitching line easier to hold at an even distance, and an edgestitch foot also helps when you close the inner stand. Neither is required to finish the collar.

Why does my collar stand not fit the neckline?

Almost always because the neckline was measured along the cut edge, where the length runs longer than the seam line, or because the placket drifted open while measuring. Measure again with the placket closed, along the seam line, and compare the result with the stand’s bottom edge before you cut.

Can I make a shirt collar pattern without pattern paper?

Yes. Newspaper, brown kraft paper, or the back of a paper grocery bag all work, because the only things the paper has to do are hold a curve and take a pencil mark. Trace the finished pieces onto card stock once the collar fits, so the pattern survives reuse.

How do I make a detachable collar from the same pattern?

Draft the leaf longer, extend both front ends by about 3 inches, and add tie strips or a buttonhole at each end. Use a firmer fusible in the leaf, finish the whole outer edge, and omit the stand seam so the collar can sit over a sweater or a tee.

Can I reuse one collar pattern on other garments?

Only where the neckline seam length matches. Copy the stand’s bottom edge length onto the new garment and compare before cutting. If the new neckline is longer or shorter, adjust the stand at center back, then redraw the leaf’s inner edge to the new stand length.

Conclusion

A shirt collar pattern comes down to two shapes drafted from one neckline measurement. Once those two pieces fit, every shirt you make gets a custom collar without a trip to the pattern shop. Measure on the seam line, raise the center front, true the stand against the neckline, then sew, grade, understitch and press. Which collar shape will you draft first, a classic point, a spread, or a rounded button-down?

About This Guide

Written and edited by Mithu for Craftsing. Mithu has 15+ years of hands-on sewing and crafting experience across mechanical and computerized machines, fabrics and techniques. This guide is research-based and draws on the SCHMETZ needle guide for needle sizing. Procedures differ by machine, so use the manual for your exact model and contact the manufacturer or a qualified technician when alignment or timing may be involved.


Affiliate disclosure: this article contains affiliate links. If you buy through them, we may earn a commission at no extra cost to you.

All images in this article were created using AI.

Share. Facebook Twitter Pinterest LinkedIn WhatsApp Reddit Tumblr Email

Related Posts

The Ultimate Guide to a DIY Sherpa Lined Vest (So Easy!)

April 21, 2026

Sew an Amazing Wine Bottle Apron: Your Ultimate Guide to the Perfect Gift!

April 9, 2026

How To Add a Contrast Bottom to a Bag: The Simple Secret to a Perfectly Sturdy Tote

April 3, 2026
Leave A Reply Cancel Reply

Our Picks

Perfect Mordanting Wool for Natural Dyeing: Secret To Vibrant, Long-Lasting Colors

The Secret to a Stunning Bathroom: An Easy DIY Wall Molding Project

15 Top Bed Sheets for Dreamy Nights: Our Expert Picks

Easy Reversible Peplum Top Pattern: One Stunning Garment, Two Amazing Looks!

Stay In Touch
  • Facebook
  • Twitter
  • Pinterest
  • Instagram
Don't Miss
Sewing Machines

Do All Sewing Machines Have Foot Pedals? 7 Checks

Not all machines need a pedal. Seven checks tell you if yours runs without one, from the socket and the start button to a knee lever and a treadle

Embroidery Removal Tool: 9 Tools, One Order That Works

December 3, 2023

Why Is My Sewing Machine Not Turning On? Six Checks

December 4, 2023

Why Does My Needle Keep Breaking? 7 Checks That Stop It

December 5, 2023
Affiliate Disclosure

Some of the links on this site are affiliate links, meaning that at no additional cost to you, I may earn a small commission if you click through and make a purchase. This helps support the website and allows me to continue creating content for you.

About Us
About Us

Discover top sewing machine reviews, expert guides, and free resources for sewing, quilting, embroidery, and various crafts at Craftsing.

Contact Us: contact@craftsing.com

Our Picks
Trending

How to Sew on a Patch by Hand: 7 Steps From Pin to Press

June 26, 2026

Sew a Stunning Swing Tunic: Your Simple Step-By-Step Guide

April 25, 2026

The Surprisingly Simple Way To Make a Hexagon Table Topper (No Binding!)

April 23, 2026
Facebook X (Twitter) Instagram Pinterest
  • Home
© 2026 Craftsing. Designed & Developed by Fixrweb.com.

Type above and press Enter to search. Press Esc to cancel.

See more from Craftsing in your Google results. Add it as a preferred source.

Ad Blocker Enabled!
Ad Blocker Enabled!
Our website is made possible by displaying online advertisements to our visitors. Please support us by disabling your Ad Blocker.