⚡ Quick Answer: How to Sew a Hole in Pants
Here is how to sew a hole in pants: trim frayed threads, then match the method to the damage. Hand darn small holes with a woven grid of stitches, zigzag larger holes with a patch behind, and sew or iron on a patch for holes over 2.5 cm, finishing with backstitches.
A hole in a favorite pair of pants is annoying, but it is almost never fatal: with the right method you can sew the damage closed so it lasts for years. This 2026 guide covers four repairs, from a five-minute hand stitch to a reinforced patch you sew on the machine.
Work through the assessment first, pick the method that matches the hole, and finish every repair with secure knots or backstitches. Your pants will be back in rotation by tonight.
The How to Sew a Hole in Pants Guide at a Glance

Match the repair to the damage before you thread a needle. Most holes in pants fall into one of four types:
| Hole type | Best method | Time |
|---|---|---|
| Tiny clean tear, edges meet, under 1 cm | Ladder stitch by hand | 5 to 10 min |
| Small worn hole, up to 2.5 cm (1 in) | Hand darning or free-motion machine darning | 15 to 30 min |
| Large hole or rip, over 2.5 cm, fabric missing | Sewn-on or iron-on patch, stitched around | 20 to 45 min |
| Seam that has split open | Restitch along the original seam line | 10 to 20 min |
The rest of this guide walks through each method step by step, starting with assessment and prep, so you can pick the right repair in seconds.
Assessing the Damage and Prepping the Pants

Wash and fully dry the pants first, since wet fabric stretches and shifts under the needle, and check the hole in good light. Measure its width and length, and look at the fabric around it: if the area is thin, grey or fraying beyond the hole, plan a patch that extends well past the damage rather than a simple stitch.

Trim every loose thread around the hole with sharp scissors until the edge is clean. Cut only the dangling fibers; cutting into the good fabric enlarges the hole and weakens the repair. Press the area flat so the edges sit level while you work.
Choosing Thread, Needles and Patch Fabric
For denim and other heavy wovens, Brother’s published fabric, thread and needle chart pairs the fabric with a jeans needle 90/14 to 100/16 and heavy-duty thread weight 30 to 50. For lighter pants such as chinos, a universal 75/11 to 90/14 with all-purpose thread is enough; for knits, switch to a ballpoint needle as the chart lists for stretch fabrics.
Match the thread color in daylight against the pants rather than against the hole: a shade slightly darker than the fabric blends into the weave better than an exact or lighter match. For the patch itself, the best source of matching fabric is the pants: cut a square from an inside seam allowance or the hem fold. Old jeans of a similar wash also make ideal patch donors.
Wind the bobbin with the same thread color, because on inside-out repairs the bobbin thread ends up visible on the right side. A fresh needle matters more than an expensive one: a bent or blunt needle causes skipped stitches that look like machine trouble.
Method 1: Hand Darning a Small Hole

Darning weaves a grid of thread across the hole, which is stronger than a single line of stitches and flexes with the fabric. Work on the wrong side with the leg stretched over a darning mushroom or a small bowl:
- Anchor the thread with a knot about 1 cm from the hole, inside sound fabric.
- Lay parallel running stitches across the hole in one direction, spacing rows about 1.5 mm apart and anchoring each end in intact fabric.
- Turn the work 90 degrees and weave a second set of running stitches over and under the first threads, like plain weaving.
- Keep tension loose so the darn lies flat; pull too tight and the fabric puckers.
- Finish with a knot on the wrong side and trim the tails.
A tidy darn in matching thread is nearly invisible on denim after a wash, and it survives flexing at the knee far better than a glued patch.
Method 2: Ladder Stitch for Tiny Clean Tears
When the two edges of a small tear still meet and no fabric is missing, a ladder stitch closes the gap invisibly. Work from the wrong side with matched thread: push the needle up through one folded edge, cross to the other side and take a small horizontal stitch about 3 mm long, then alternate sides stitch by stitch. Pull gently every few stitches so the gap closes into a flat line, start and finish about 1 cm into intact fabric, and knot on the inside.
If the tear sits at a seam allowance or pocket edge where you cannot reach the wrong side, use a whip stitch over the edge instead; it is slightly more visible but holds well in high-stress spots.
Method 3: Free-Motion Machine Darning
For speed on small to medium holes, machine darning with the feed dogs dropped (or covered, as your machine’s manual describes) lets you move the fabric yourself. Slip a small piece of lightweight interfacing behind the hole so the needle has something to bite, hoop the area if you have one, set stitch length to 0, and sew parallel lines about 1.5 mm apart across the hole, then rotate 90 degrees and cross them. The Brother video below shows the free-motion principle on a Brother machine:
The video above is from the official Brother support channel on YouTube (@BrotherSupportSewing) and shows free-motion quilting, which is the same fabric-guided technique used for machine darning. Feet, feed dogs and settings differ on other models, so follow the manual for your exact machine.
Move the hoop in one steady direction and keep stitch density even; jerky movement makes some areas dense and others sparse. Ease off gradually as you move into sound fabric so the repair blends in.
Method 4: Sewing on a Patch for Large Holes

Cut the patch about 2.5 cm (1 in) larger than the hole on every side and round the corners, because square corners peel first. Turn the pants inside out, pin the patch behind the hole with the right sides facing each other, and slide the pant leg onto the machine arm so the patch sits under the needle:

- Sew a straight stitch around the patch perimeter, 3 mm from its edge, catching both layers.
- Add parallel rows across the whole patch every 6 mm in both directions, extending 1 cm into the intact fabric.
- Backstitch at the start and end of each row.
- From the right side, zigzag over the hole edge so no raw fabric shows.
- Trim the original fabric behind the patch to within 6 mm of the hole to reduce bulk.
Stitching the Patch on the Machine: Zigzag and Stitch Settings

A wide zigzag over the hole edge and around the patch keeps the repair flexible under stress, and a stitch regulator keeps free-motion lines even. Set a zigzag about 3 to 4 mm wide and 1 to 1.5 mm long for denim, sew slowly, and let the feed dogs pull the fabric rather than pushing it. The Brother video below shows how the stitch regulator evens out free-motion work:
On very thick seams, slip a hump jumper or a folded piece of card behind the presser foot so it stays level instead of climbing the bulk.
The video above is from @BrotherSupportSewing on YouTube and shows the stitch regulator used for free-motion work on a Brother machine. Regulator availability and stitch tables differ on other models, so use the manual for your machine to pick settings.
Iron-On Patches as a Fast Fix

For a quick fix, an iron-on denim patch goes on the inside of the leg, adhesive side against the wrong side of the fabric, pressed through a cloth for the time the package lists (usually 15 to 20 seconds, lifting and repositioning rather than sliding). A 20-piece cotton denim patch kit in several washes, such as the KING MOUNTAIN iron-on repair patches, covers a hole now and the next one later. Check Price on Amazon.
Treat the glue as a temporary hold: after it cools, sew a zigzag around the patch edge, or the repair will peel after a few washes. Iron-on alone is fine for a costume or a child’s play pants but not for daily wear at the knee.
Common Mistakes When Mending Pants
| Mistake | Why it fails | Fix |
|---|---|---|
| Cutting into the hole while trimming | Enlarges the hole and weakens edges | Snip only dangling threads |
| Patch smaller than the hole | Stress concentrates at the edges | Cut 2.5 cm larger all around, round corners |
| Starting exactly at the tear edge | Repair reopens at the same spot | Anchor 1 cm into intact fabric on each side |
| Iron-on patch with no stitching | Adhesive peels after washing | Zigzag around the patch edge |
| Universal needle in denim | Needle snaps or skips stitches | Fit a jeans needle 90/14 to 100/16 |
Check your repair against this table before you call it done; each fix takes seconds now and saves unpicking later.
One more habit worth building: when you notice a worn patch of fabric that has not torn yet, reinforce it immediately with a patch or a few rows of stitching. Preventive mending takes ten minutes and saves the garment from a full hole later.
High-Stress Spots: Knee, Inner Thigh, Crotch and Back Pocket
Knees and back pockets take abrasion, and the inner thigh and crotch take friction from walking and sitting. For these spots, always patch from the inside with matching fabric, stitch the perimeter and add the crosshatch rows, then add a few bar tacks at the corners of the patch. If the fabric around the hole is already thin, reinforce it with a second layer of patch fabric before it rips open, because stitching into worn fabric only tears it further.
For back pocket holes specifically, a small square of fusible interfacing fused over the hole on the inside and then stitched around is often enough, because the pocket bag supports the area from behind.
Mending Stretchy Pants and Leggings
Leggings, joggers and knit pants need stitches that stretch. Use a ballpoint needle 75/11 to 90/14 as Brother’s chart lists for knits, and a narrow zigzag about 1.5 to 2.5 mm wide. When several layers meet at the crotch, a walking foot evens out the feed and stops the top layer stretching, as explained in our stretch fabric guide. Hand darning also works on small knit holes if you keep the tension loose. Avoid pulling the fabric taut while you sew stretchy material; let it feed naturally so the seam keeps its give.
Machine Troubleshooting, Prevention and Care
If the machine skips stitches or will not start while you mend thick layers, check the basics first; our foot pedal repair checks covers the seven usual culprits before you assume a breakdown. To prevent future holes, reinforce inner thighs with a patch before they wear through, wash pants inside out on a gentle cycle, and line dry them, since dryer heat weakens fibers.
After mending, check the repair after the first wash; if any stitch loosened, restitch it the same day while the hole is still small.

Frequently Asked Questions
What is the best way to sew a hole in pants?
Here is how to sew a hole in pants: trim frayed threads, then match the method to the damage. Hand darn small holes with a woven grid of stitches, zigzag larger holes with a patch behind, and sew or iron on a patch for holes over 2.5 cm, finishing with backstitches.
Can you sew a hole in pants by hand?
Yes. Small holes under about 2.5 cm (1 in) mend well by hand with a ladder stitch or a darned grid of running stitches. Use thread matched to the pants and anchor every row into sound fabric at least 6 mm beyond the hole.
What thread and needle should I use for jeans?
Use a denim or heavy-duty thread in a shade slightly darker than the fabric, and a jeans needle 90/14 to 100/16, which Brother’s fabric chart lists for denim and canvas. Match the bobbin thread too, since it shows on the wrong side.
How big does a hole need to be before it needs a patch?
Any hole wider than about 2.5 cm (1 in), any ragged tear with missing fabric, and any area worn thin around the hole calls for a patch. Small clean holes stitch closed without one.
Do iron-on patches last on pants?
On their own the adhesive usually fails after some washes, so treat an iron-on patch as a base layer and sew around its edge with a zigzag. A sewn patch from matching denim outlasts the glue by years.
How do I fix a hole in the inner thigh or crotch?
Turn the pants inside out, pin a matching denim patch behind the hole, and stitch a zigzag around the perimeter plus parallel rows across the patch in both directions, extending 1 cm into the intact fabric. Bar tacks at stress points add strength.
How do I mend holes in stretchy pants or leggings?
Fit a ballpoint needle 75/11 to 90/14 as Brother’s chart lists for knits, and use a narrow zigzag so the repair stretches. A walking foot helps feed the layers evenly, as our stretch fabric guide explains.
How do I stop holes from coming back?
Reinforce high-rub spots like inner thighs with a patch before they wear through, wash pants inside out on a gentle cycle, and skip high dryer heat, which weakens fibers over time.
Conclusion
Knowing how to sew a hole in pants turns a would-be donation into a wardrobe staple: assess the hole, pick the matching method, and finish with secure stitching. Small holes take minutes by hand, and a well-patched knee can outlast the rest of the jeans. Keep a small mending kit in a drawer so a hole never gets the chance to grow overnight. Which pair are you mending first?
About This Guide
Written and edited by Mithu for Craftsing. Mithu has 15+ years of hands-on sewing and crafting experience across mechanical and computerized machines, fabrics and techniques. This guide is research-based and draws on Brother’s fabric, thread and needle chart, which sets the jeans needle 90/14 to 100/16 for denim and the ballpoint 75/11 to 90/14 for stretch knits, and on Brother’s operation manuals for zigzag and free-motion guidance. The two embedded videos are from the official BrotherSupportSewing YouTube channel. Procedures differ by machine, so use the manual for your exact model and contact the manufacturer or a qualified technician when a step depends on your machine.
Affiliate disclosure: this article contains affiliate links. If you buy through them, we may earn a commission at no extra cost to you.
All images in this article were created using AI.


